Some updates of some work i did a few weeks ago
Wanted to get the engine prepared to be taken out of the engine bay. As i haven't the use of an engine crane, i used 2 car jacks, a car stand, crow bar and my two arms to get it away from the chassi!! I was going to try and raise the car up over the engine, but after getting the engine free from the chassi, the car would have had to have been raised about 5 feet to get the engine out, because of the corollas lower front bar, and as im doing this in my driveway, i didn't want to risk any accidents!! So, heres the work so far.
First, the tools!
The culprit!!
I took some pictures of the fuels lines to and from the charcoal swirly pot and the intake, just so i know where everything goes.
Me, pointing at stuff!!
More pointing.
After market fuel pressure regulator on the right there.
Unscrewed line from swirly pot to injectors.
Unplugged lines from pot to engine and pot to fuel lines.
Unscrewed fuel pressure regulator from chassi.
Unplugged fuel line from regulator.
Then started to take the rear engine mount bolts off. I had these already loosened so just a few turns to get them off.
View from underneath the car out of the bonnet. Nice day :
:
Nuts are off the rear engine mount. Photographed them for size reference.
Used long torque wrench to unloosen the front engine cradle from the chassi. IMPORTANT TO NOTE!! The left gearbox side engine mount and the right timing belt side engine mounts are still bolted to the chassi and engine, and the bolts from the engine mount are still inside the metal of the cross member (2 of them) with one bolt aslo holding the engine cradle in place (four pictures up!)
14mm socket used.
Engine cradle just drops down.
It is still being held in by the 3rd bolt on the rear engine mount tho. This is what starts causing problems getting the engine free (as i found after a lot of f'ing and blinding and basically throwing a few tantrums in the middle of the drive way in front of the neighbours!! ahem...) because, IMPORTANT TO NOTE!! the engine has to be lifted for it to pop out, and it cant be lifted up until the gearbox side mount is unbolted, this is where an engine crane comes in handy!! or, as i did, the use of carefully placed car jacks!! I managed to wiggle it out using carefully placed pieces of wood, wrestling techniques, and down right super powers!!
Also to, the engine had to be raised with jacks after unbolting the gearbox side mount, and lowered on the timing belt side slightly after unbolting the timing belt side mount, so that the engine was at a slight angle so it could be wiggled and pryed out. The reason for this is that if you try to just raise the engine up and pop the rear engine mount bolt out of the cross member, the engine mount hits off the steering racks that goes toward the passenger side wheel!! Found this out after asking "WHAT THE F%&K" about 3 times!!
So your beggining to see what kind of day i had haha. I'm sure someone is asking..."why didn't you just unbolt the mount from the gearbox". Good question! I couldn't because (A), one of the nuts is worn, and (B) there was no space to fit the socket wrenches in to get at them, and also the spanners were just feck'n useless!! i could have also just unbolted the gearbox and dealt with it in two pieces, but again had issues trying to get at bolts!
here are the photo's. I'll explain as i go...
By the way, i had to get the engine cradle out so i could drop the engine down.
picture under the car of the rear engine mount. You can see where the 3rd bolt is holding the engine cradle in place
Jacking up the engine to hold it in place as i unbolt the gearbox side engine mount (pre-loosened on the chassi (the bolt that goes sideways through the rubber mount), but still bolted tight to the gearbox)
Gearbox side engine mount
Taking out the side bolt. Saying a little prayer that i don't get my fingers caught!!
Unbolting the gearbox side engine mount bracket from the gearbox.
Using a second jack to balance the front of the engine as i could feel the weight tilting forward
Mount comes off.
After raising the engine with the jacks and trying to pry the rear mount bolt from the cross member and engine cradle, i found that i needed just a bit more space to get it free so i took off the gearbox engine mount bracket bolted to the gearbox (under the mount) When that didn't work, i lost the plot a bit!! :banging:
Jacked up the driver side of the engine to unbolt the timing belt side engine mount.
Started unscrewing from underneath the mount.
After unscrewing a couple of smaller nuts on top, the engine came free from the mount.
I then lowered the engine on the driver side so its tilted to one side, so i could start getting the rear engine mount bolt free from the engine cradle and cross member.
This is a picture looking down on the rear engine mount behind the gearbox. You can see just above the mount, it is being stopped by the steering rack that goes to the passenger wheel. This was a complete pain in my arse for at least 20 minutes!! you can also see where the mount is bolted to the gearbox, the top bolt is worn and there's no space to get the socket wrench in their!! This is all very important information as it will help future nutters to avoid heart attacks and serious angry outbursts hahaha.
Then i had the bright idea of leaving the engine raised and lowering the car more so maybe the bolt would come free from the cross member and engine cradle.
But then i had the same trouble with the mount being stopped by the steering rack. Tantrum number 3!! :crying: So then i decided, enough mess'n about and used the crow bar to wedge the bolt out a bit, a piece of wood to jam in between the mount and the crossmember, and my arms to wiggle the shit out of the engine until...Eureka, the engine came free!!! :
:
Out comes the engine cradle...
And the engine drops to a pallet underneath!!
I then sat down and stared at it for about 15 minutes with a big stupid grin on my puss!!
I called it a day after figuring out it might be a little dodgy to raise the car up so high to drag the engine out, but its now away from the chassi and ready to be lifted out come BEAMS fitting day!! :thum:
A few weeks ago, i filled the cylinders of the BEAMS with WD40 and some anti rust oil and its been sitting in there to a good while, so going to unseize it when it gets fitted. my mate noel has done this plenty of times so i think il leave that job to him!
Trusty turkey baster :thum:
WD40
Filled turkey baster with WD40
Filled each cylinder.
And finally, Today my clutch kit arrived, so il be putting that on over the weekend :
:
Thats all for now. More updates soon, Hopefully the next photo's youl see will be the BEAMS engine in the Corolla engine bay!
Wed Mar 27, 2024 12:39 am by jorpakko
Calendar
